Silicone C Class Baking Varnish

Home Products Silicone C Class Baking Varnish
High Temperature Silicone Grade

Silicone C Class Baking Varnish in India

Most insulating varnishes hit their limit somewhere between 130°C and 180°C. Beyond that, ordinary alkyd and phenolic resins start to lose their mechanical and dielectric properties, no matter how well they were formulated. That's the exact gap our Silicone C Class Baking Varnish is built to close — a silicon resin-based formulation engineered for insulation Class C, the highest thermal rating in standard electrical insulation classification, covering operating temperatures above 180°C.

Silicone-based chemistry is chosen here for a reason: it retains its structural integrity, flexibility, and dielectric strength at temperatures where conventional organic resins would degrade. That makes this grade particularly relevant for equipment that runs hot as a matter of routine, not as an occasional stress condition.

Silicon resin base built Retains flexibility and mechanical strength Strong bonding once cured, similar Good resistance to moisture, chemicals,
KEY PERFORMANCE ADVANTAGES

Special Key Features

What sets a good insulating varnish apart isn't just that it dries it’s how the cured film behaves afterward. Our air drying formulations offer:

Silicon resin base built for Class

Silicon resin base built for Class C thermal ratings (above 180°C)

Retains flexibility and mechanical strength

Retains flexibility and mechanical strength at elevated operating temperatures

Strong bonding once cured, similar

Strong bonding once cured, similar to our other baking impregnating varnishes

Good resistance to moisture, chemicals,

Good resistance to moisture, chemicals, and hot transformer oils

Suitable for high-load electrical equipment operating

Suitable for high-load electrical equipment operating continuously at high heat

Bake-cured film offering more rigidity than

Bake-cured film offering more rigidity than air-drying alternatives

Process Guide

Application Method

Like our other baking impregnating varnishes, this silicone-based grade is typically applied by dipping, with vacuum pressure impregnation (VPI) also used where deeper penetration into winding gaps is required. Once applied, the component goes through a controlled bake cycle in an oven to fully cure the resin into a hard, bonded, heat-stable film.

Given the high-temperature service this varnish is meant for, it's worth working closely with our technical team on recommended bake schedules specific to the winding type and thermal load involved, since silicone-based systems can behave differently from alkyd or phenolic formulations during cure.

Recommended Application Modes
1
Spraying
For uniform coverage on large batch components
2
Brushing
Simple hand application for small components or repairs
3
Dipping
Full submersion for complex-shaped parts
4
60-Min Second Coat
Re-apply after 60 min for extra protection
Technical Parameters

Specifications

Formulated as a silicon resin-based baking varnish rated for Class C thermal insulation (above 180°C). Specific viscosity, bake schedule, and coverage details are available through our technical data sheets on request, tailored where needed to the client's specific application.

Thermal Class Class B (130°C), F-Class & H-Class Available
Resin Foundation Phenolic Resin-Based Formulations
Curing Mechanism Room Temperature Air Drying (Heat Optional)
Operating Climate Typically 0°C to 55°C Ambient Range
Available Shades Clear, Golden, Amber Shades
Versatile Protection

Uses & Applications

This varnish range is used extensively as a finishing, impregnating, and protective coating across a wide set of electrical applications, including:

Motors and generators operating continuously

Motors and generators operating continuously at very high temperatures

Transformers and electrical components exposed

Transformers and electrical components exposed to sustained heat loads

High-voltage machinery where thermal cycling is

High-voltage machinery where thermal cycling is frequent and severe

Equipment where standard B, F,

Equipment where standard B, F, or H-Class varnishes would fall short of thermal requirements

General protective coating for industrial equipment

General protective coating for industrial equipment

Across all these applications, the core job stays the same — shielding sensitive electrical parts from moisture, chemical exposure, and the general wear of daily operating conditions.

MANUFACTURING TRUST SINCE 1988

Why Choose Us

Formulating a genuinely high-temperature-stable varnish isn't something that can be improvised — the resin chemistry has to hold up consistently, batch after batch, at temperatures where most coatings start to fail. The quality of our Class C silicone-based varnish, which we test in our own laboratory for thermal stability, adhesion and chemical resistance, is no different from the quality of our other varnishes.

But it is especially important to our clients who operate heavy-duty electrical equipment where thermal class is not an extra specification, but a critical one.

Trusted by Leading Names

Proven across critical applications in power, railways, defense and manufacturing:

NTPC Indian Railways HAL Tata ONGC Adani Polycab L&T
Got Questions?

FAQs

Silicone C Class Baking Varnish is engineered for coating, insulating, and protecting industrial components.

It can be applied via spraying, dipping, or brushing depending on application needs.

We manufacture grades covering B-Class, F-Class, and H-Class thermal requirements.

Yes, matching thinners can be used to achieve optimum application viscosity.

All products are manufactured at our facility in Ahmedabad, Gujarat with ISO 9001:2015 certification.

Explore Our Complete Silicone C Class Baking Varnish Range

Find the exact formulation for your motor winding, transformer coating, or industrial application.